How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
Almost everyone has got their private idea when it comes to How to Install a Bathtub Yourself.
Installing a bathtub isn't precisely rocket science, but it does require strong plumbing, carpentry, and in some cases, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is conveniently available, the project can relocate immediately; if you need to open up a wall to eliminate the old bathtub and also place the new tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will require an assistant to leave the old bathtub and also set in the new one. Ensure you have actually certified yourself for the job as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is far better to consider using one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This post will certainly aid you install a brand-new bathtub in your restroom if you have actually currently acquired a new bathtub as well as do not need to change the plan of your previous water supply pipes.
Your tools and also material list should comprise the following:
Getting ready for the Setup
Firstly, the supporting structure provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps system to stop stress on the bathtub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the limited accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipes. Once the supply pipes have been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming during this process. As soon as the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Using both wooden boards under its feet, place the bath tub in the called for position. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub up until the level reviews level.
To set up taps, fit the bottom of the furthest versatile faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
Switch on the water system and inspect all joints as well as brand-new pipework for leakages and also tighten them if required. Fill the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub ought to wait until the bathtub has actually been made use of at least once as this will certainly resolve it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area between the tap and the sink. Secure the tap in position with the supplier provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical faucet connectors. The previous kind needs to be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack an inflexible seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and also cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to securing, to enable the movement experienced when the tub is in usage. The sealant can split relatively early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very occupied with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you liked the new blog entry. Don't hesitate to take a moment to distribute this write-up if you enjoyed reading it. Thank you for taking the time to read it.
Schedule Here
Report this page